Media

 PXH
 PXH
 PXH


Description

Reznor's PXH are configurable air handlers. The units have forward curved blowers allowing for standard or high efficiency motors and VFD control. 

An optional hydronic heating coil module can also be added. The coil is constructed of turbo spiral tubing. Choose from left or right connections.

Note: For proper coil size selection use RezProToolbox software selection program. Altitude and glycol content must be specified.

Heating Range ( MBH )

Cooling Range ( MBH )

Airflow Range ( CFM )

Standard

  • ETL certification
  • Pre-coat white gloss cabinet finish (all units); 60 gloss minimum and RAL 9001
  • Circuit breaker protected transformer for 24-volt controls
  • Vibration/noise isolated venter motor, blower(s) and blower motor (spring or rubber isolators)
  • L50 bearing rating with a life expectancy of 150,000 hours
  • Airflow pressure switch to verify circulating blower operation on makeup air options
  • Socketed, high quality switching relays to facilitate service
  • Through-the-cabinet or through-the-base electrical
  • Three hinged service doors with heavy duty hardware
  • Slab or floor mounted; or ceiling suspended (4, 6 or 8 point base suspension based on modules selected)
  • Fork lift openings built into the heavy gauge steel base 
  • Discharge duct flange

FACTORY INSTALLED OPTIONS

  • UV germicidal lamps - ultraviolet emitter for neutralization of VOCs and airborne micro-organisms for improved IAQ - not filtration. (Requires cooling coil cabinet Option AU. Separate 115/1 or 208/1 or 230/1 wiring/ breaker and a separate disconnect must be provided.)
  • Cooling coil module with coil
  • Supply voltage - 115/1; 208/1; 230/1; 208/3; 230/3; 460/3; 575/3
  • Unit mounted, lockable, non-fused service on/off switch
  • Inlet air filters - 1” or 2” disposable or permanent; 1”, 2”, or 4” pleated disposable; arranged in vertical flat bank for ease of service
  • Convenience outlet (requires separate power supply)
  • Controls-
    • Space or discharge temperature heating/cooling (FX06/07 platform) (optional room command module required for space control)
      • Digital single-stage modulating heating (hydronic valves supplied by others)/three-stage cooling, dedicated DX reheat control system
      • Digital electronic modulation heating (25% low fire - natural gas, 40% low fire - propane)/ three-stage cooling, dedicated DX reheat control system
    • Thermostat discharge temperature heating/cooling makeup air
      • Digital two-stage heating/three-stage cooling
    • Modulating thermostat for heating/cooling
    • Thermostat for 2-stage heating/3-stage cooling
  • Cabinet configuration and construction
    • Left or right side controls
    • No insulation; single or double wall with standard insulation (Model PXH)
    • High R-value insulation (all units)
    • Blower cabinet screen (Model PXH)
    • Inlet duct connection flange, or inlet on/off damper with duct flange
    • Discharge duct flange or louvers (horizontal or horizontal and vertical) (Model PXH)
    • Blower cabinet screen, inlet duct connection flange, or inlet on/off damper with duct flange
  • Mixing Box Module
    • Five inlet configuration combinations including top, bottom, and rear (Model PXH)
    • Three inlet configuration combinations with 100% bottom return air opening and/or 100% outside air rear opening (Model RXH)
    • Inlet air configuration with 30% outside air opening and 100% return air opening (Model RXH)
    • Manual, motorized 2 or 3 position, motorized modulating return air or outside air and return air dampers
    • Direct-coupled 24VAC damper actuators
    • Damper control selections such as 0-135 ohms resistance potentiometer, building pressure, or 0-10 v control
    • Bottom return air screen (Model RXH)
  • Double wall downturn plenum cabinet (Model RXH)
    • Shutoff dampers
  • Blower motor (1/4 to 5 HP) - see pressure drops and blower charts
    • open dripproof, TEFC, or premium efficiency
    • adjustable sheave and belt
    • motor contactor; IEC motor starter; or factory-installed variable frequency drive
  • Hydronic heating coil and module, blow-through (valves to be supplied by others)
    • For proper selection, use Reznor coil selector software included in RezPro® Toolbox (calculator required for proper altitude and glycol content)
    • Left or right coil connections
    • Turbo spiral tubing
  • Cooling coil module with coil
    • ♦DX coil (single, dual or 1/3-2/3 circuit; galvanized or stainless casing; copper or aluminum fins (coated or uncoated) - non-ozone depleting, R410A refrigerant
    • ♦chilled water coil (3-45 tons; 1/4, 1/2, 3/4, or full circuiting; galvanized or stainless casing; copper or aluminum fins (coated or uncoated)
  • DX coil module with dehumidification control. Single, dual and 1/3-2/3 circuit, main DX coil with modulating or standard reheat control
    • Separate compressor for dehumidification system
    • Hot gas bypass
    • Modulating control
  • Evaporative cooling module
    • white pre-painted or 300 series stainless steel cabinet
    • 300 series stainless steel reservoir
    • Recirculating pump or AquaSaver microprocessor-based, timed water distribution system
      • Water recirculating pump with optional (field installed) fill and drain kit
      • AquaSaver water metering device with optional (field installed) freeze protection
    • 12” CELdek® or GLASdek®UL 900 Class II noncombustible media
    • 1” or 2” aluminum pre-filter
    • Water hammer arrestor (field installed)
  • Over/under voltage or phase loss protection
  • Discharge air temperature low limit

FIELD INSTALLED OPTIONS

  • Variable frequency drive (factory-installed is also available)
  • Smoke detector (in ductwork)
  • Remote control console and unit monitoring
  • Fusible and non-fused disconnect switch (NEMA 3R) (Model RXH)
  • 16” insulated roof curb (Model RXH)
  • Intake air hood with rain baffles (Model RXH)
  • Perimeter roof curb transitions to (C)RGB/RPB roof curbs - for replacement of Models (C)RGB/RPB (Model RXH) (Not available for units with hydronic heat)
  • Thermostats to match analog controls
  • Downturn nozzles (25-65° or 50-90°) with directional louvers (Model PXH)
  • Main unit disconnect switch
  • M-Series condenser

 


Brochures
4 Files

Brochures


English
Split System Marketing Catalog
Split Systems Marketing Catalog
Download File
886.0 kB
Comp Edge: The wide range of options and features of PreevA and the M-Series Condensing unit
Competitive Edge: The wide range of options and features of PreevA and the M-Series Condensing unit
Download File
599.9 kB
Energy Edge: By matching building heating and cooling needs, the PreevA Series can save energy
Energy Edge: By matching a building heating and/or cooling needs (at full or part load), the PreevA Series can save energy and provide more consistent comfort levels
Download File
486.7 kB
Heating, Cooling, Ventilation & VRF Product Line
Heating, Cooling, Ventilation & VRF Product Line Sheet
Download File
630.7 kB

Technical Data
2 Files

Technical Data


English
Catalog - Split System
Commercial split systems catalog
Download File
3.3 MB
Sample Specs - PEH & PXH
Sample specifications for Models PEH & PXH (Word document)
Download File
17.2 kB

Service/Installation
11 Files

Service/Installation


English
Unit Installation Manual - Indoor PreevA
Installation Manual for Models PDH, PEH, PXH, SDH & SHH
Download File
2.7 MB
Parts Manuals - PREEVA
Replacement parts for PREEVA Models PDH, PEH, PXH, RDH, REH, RHH, RXH, SDH, and SHH
Download File
10.5 MB
Option - Installation - Downturn Nozzle Installation - Indoor PreevA
Installation of downturn nozzles for indoor PreevA units
Download File
753.7 kB
Option RB5 - Installation - Remote Display
Installation instructions for optional remote mounted display for PreevA & MAPS Series, and Model ZQYRA
Download File
335.8 kB
Controls - D19, D21, and D22 Control Manual
Air handler system control options D19, D21, and D22
Download File
1.2 MB
Operation - PreevA
Operation, maintenance and service manual for PreevA systems, Models SHH, RXH, RDH, REH, PXH, SDH, PDH, & PEH
Download File
861.1 kB
Field Service - Adjustment of Control FX06 - PreevA
Application and instructions for field adjustment of the contorl (Model FX06) in digital control options D12B, D12C, D12D, D12E, D12F, & D12G for PreevA units
Download File
766.6 kB
Field Service - Damper Motor Replacement
Instructions for replacement kit (261697) for Belimo damper motor
Download File
161.8 kB
Field Service - Replacement of Discontinued Relays
Installation for kits designed to replace relays no longer available from suppliers. Applies to all Reznor units using obsolete relays.
Download File
340.4 kB
Français
Manuel d'installation - Intérieur PreevA
Manuel d'installation applicable aux: unités de traitement d'air modèle PDH, modèle SDH, modèle PEH, modèle PXH et modèle SHH
Download File
3.4 MB
Opération - Série PreevA
Opération, maintenance et réparation PreevA ® Modèles RHH, SHH,  PDH, PEH, PXH, SDH, RDH, REH, et RXH
Download File
2.2 MB

Other Files
1 File

Other Files


English
Warranty Statement
Reznor equipment limited warranty statement
Download File
183.4 kB